How to Install a PVC Fence

There are some things to be aware of when you're contemplating installing fencing. First, you must decide the location where you would like the fence to be placed. Next, prepare the ground. Then, you'll need to put in the posts. You may also need to alter the height of the fence based on the size of your property.

Preparing the ground

It is important to prepare the ground for the fence. This is because fence posts have to be placed in a secure manner. The fence will easily fly away if not secured.

Before you begin digging, you must check with your local utility company to ensure that there aren't any underground utilities that could interfere with the construction. In many regions, you can call 811 and have the utility company mark your yard for underground lines.

A gravel base should be prepared for the fence posts. This will allow water to drain from the posts. It also provides a solid base on which the blocks will be built on top of it.

Once you have the base, you can begin to install the vinyl fence. The material should be at a minimum of four feet long and 1 inch thick. If you have access to an auger, then you can utilize it to dig the holes for the fence posts.

Before digging, you should remove any plants and trees which could block the hole. Sometimes, it is easier to remove the soil rather than dig it. If you do have to dig, you should try to stay clear of digging in rocky or sandy soil.

Next, mark the high and lowest points of your yard. This can be accomplished by using a string level. Attach the string level to stakes about one foot above ground. The string level acts as a guide for fence posts.

If your property is located in a very dry climate, it is likely that you have to drill pilot holes prior to drilling. This will speed up the process.

You will also need to mark the holes. You can use spray paint or a marker to mark your holes. You can also make use of a mason's line to make sure that the posts are straight.

You can also fill the gap with decorative stones. These stones are best suited for smaller gaps. However in the event that there is a larger gap, you'll require a different strategy. You could also try putting dirt inside the gap. This is a cost-effective and PVC efficient solution.

Placing the posts

Installing the posts can be a daunting task. The first step is to find the proper place. You can use a spiral level, a mark made to determine the size of the posts, or a measuring instrument.

Then, install the posts that are at the corner and PVC the end. Also, put in the top and middle rails. Some cutting might be necessary. Rails can be used as an alternative to posts as a spacer.

Once you have found the middle of each hole with a tape measure or stakes, mark the middle of the posts with a tape measure. To determine the depth, you can also use the stringline. Once the string line is drawn, tie the ends of the post to the string. This will ensure that the fence will be straight.

After the posts are seated after which you can fill the bottoms with 6 inches of gravel. This will keep the posts in place and also provide drainage.

Use a quick setting concrete when putting fence posts in concrete. It is a form of concrete that sets in three to four minutes. It is recommended not to put too much pressure on the panels when installing privacy fencing. The panels should sit 22 inches above the ground. The panels is to be secured using #10 x 1" self tapping stainless steel screws.

If you are installing a vinyl fence you can join the posts to the bottom collars by using two screws. If you are installing a privacy fence you must leave one screw at the top rail. Duct tape can be used to cover the bottom horizontal rails prior putting them into the posts. This stops concrete from getting into the horizontal rails at the bottom.

Once you are happy with the layout, peel off the duct tape. Then, insert the top rail into each of the posts. The pickets may be attached to the rails.

You can also set the bottom rails at the corners. Aluminum u-channel can be used to connect the rails to your posts.

Assembling the panels

The alignment of the fence posts up correctly is crucial to the success of installing a vinyl fence. It is possible to employ different techniques depending on the design of your fence. If you're installing an oval or square fence, there are a few steps to start you off.

Before you begin, ensure that you review your deed as well as local Zoning laws. Notify neighbors about your plans. You might need an building permit when you are planning to put up a white vinyl fences fence.

Once you have all your posts set, it's time to set up your rail brackets. These screws are attached to the inside of the post. This allows for a more efficient manipulation of the posts as they are placed.

Before putting up your rail brackets, install the bottom rail. Pre-assembled vinyl picket fences panels usually have two rails. You may have to modify the rails to fit your terrain.

Once the bottom rail is installed then you can put in the middle rail. The top rail can be set up in the same manner. This step can be done using an aluminum uchannel. It is inserted into your posts with the help of #8 1 inch screws.

Then, you can install your pickets one by one. Once they are all in place then you can begin attaching your C channel brackets. You can also place stakes around the corners to hold them in place. To join stakes, you can use cotton string.

Spray paint markers can be used to mark your line. This will ensure that the fence is straight when it is set.

Then, you must install your privacy fence panels panels. These should be installed on the back of your fence. You can also add pea gravel to your holes to keep them in place. You can make your slope gentler by placing your fence panels at one side so that they "step down". However, if the slope is steep then you'll need to set up your fence so that it "steps down" from the top to the bottom.

Problems with changing heights

If you're looking to put a PVC fence you might face difficulties in lining up the posts. There are two methods to do this. The first is to put the posts on the ground. The other is to line them up. The first option is easier to apply and ensures there is concrete under and around the post. In the second method, you will have to dig out the posts, and then backfill with dirt.

When you remove the posts, make sure to use a quality backfill and dig the holes enough to hold three-quarters of the length of the post. It is necessary to dig down approximately six inches to sink the posts into the bottom of the gravel. You can also use a hole digger to make holes. The tension bar can be attached to the mesh in the final step. Attach the steel mesh on the top to the fence.

If you're having issues getting the posts in line and you are having trouble, you can remove the rail from the posts that are too high. This is a challenging procedure however you will be able to accomplish it if you have two people working with you. You can tighten the bolt threads using either a hammer or an axe. This will stop them from escaping the fence when you take it off.